Skip to content
PropertyRoofs

Silicone roof coating

Silicone roof coating is a liquid silicone that is rolled or sprayed over an existing roof and cures with moisture from the air into a seamless, elastic layer. Makers sell it for spray foam, metal, single-ply and asphalt roofs, and say it withstands ponding water. The trade-offs are dirt pickup, a slippery surface and recoats that have to be silicone too.

ASTM standard
D6694, written for coatings over spray foam
How it cures
One component; reacts with moisture in the air
Volume solids
91 to 96% solvent-free; 69% solvent-borne
Ponding water
Makers say it withstands it; warranties may still exclude it
Recoat with
Silicone
Warranty available
10 to 20 years by thickness; 25 from one maker

What silicone roof coating is

Silicone roof coating comes as a single-component liquid that cures by reacting with moisture in the air, so there is nothing to mix. The cure starts once a pail is opened, and makers warn against spraying it through hoses that have carried water-based acrylics, because the hose liners hold moisture.

Most silicones sold for commercial roofs are solvent-free and high in solids. Gaco, Henry, Karnak, Polyglass, American WeatherStar and Sika list 91 to 96% solids by volume and under 50 grams per liter of VOC. Solvent-borne silicones are still sold at about 69% solids and up to 250 g/L, so a gallon leaves less coating on the roof once it cures.

ASTM D6694 is the standard specification for silicone roof coatings. Its scope is a coating used as the roofing membrane over spray polyurethane foam, with a polymer that is more than 95% silicone, and it gives no guidance on application. Makers cite it for products they sell for many roof types: Gaco, Tremco, Henry and Polyglass data sheets say their silicones meet it.

Pros and cons

Where silicone coatings work

  • Makers say it withstands standing water: Gaco, Henry, Karnak, Polyglass and Momentive all claim it for their silicones.
  • High solids mean most of what goes on stays on: Everest lists 14 dry mils from a gallon per 100 sq ft of its 90%-solids silicone.
  • Some products go on in cold weather: Gaco's S42 and Everest's Silkoxy H3 can be applied down to 32°F.
  • Some are rain-safe quickly: 15 minutes for Henry's 887, and an hour for Gaco's S42 and Momentive's Enduris 3500.
  • New white silicone is very reflective: about 0.87 initial solar reflectance in Cool Roof Rating Council listings.

Where they fall short

  • Only silicone sticks to silicone, so every later recoat and repair has to be silicone.
  • It holds dirt, and rated white silicones fall from about 0.87 to 0.67 to 0.69 solar reflectance after three years outdoors.
  • It is slippery, especially when wet, and needs granules or walkway pads where people walk.
  • Over asphalt roofs, oils can bleed into it and stain it, so it needs a bleed-blocking base coat, and Gaco allows only white silicone there.
  • Makers rule it out over cold storage buildings without a vapor barrier.

How it's applied

  1. Check the roof for trapped moisture. Gaco requires a nuclear or infrared scan, with any wet roofing removed and replaced, and Karnak says not to coat a roof that is 20% or more wet.
  2. Clean it. Momentive's recoat guide starts pressure washing near 1,000 psi and raises the pressure only as needed, without forcing water into the roof.
  3. Test adhesion. A fabric strip is set into a patch of coating, left to cure and pulled; Momentive and American WeatherStar pass the test at 2 pounds of pull per 1-inch strip.
  4. Prime where the roof calls for it: a bleed-blocking base coat over asphalt roofs, a rust-inhibiting primer on rusted metal, and a primer or cleaner on some single-ply membranes, depending on the maker.
  5. Apply it by roller, brush or airless sprayer. A common single-coat rate is 1.5 gallons per 100 sq ft, about 24 wet mils, for 21 to 22 dry mils. Granulated and other rough surfaces take more for the same thickness.
  6. Check thickness as it goes on with a wet mil gauge. Gaco recommends adding 10% to make sure the coating reaches the minimum dry thickness its warranty requires.
  7. Keep traffic off while it cures. Gaco's S42 data sheet says 24 to 48 hours before light foot traffic, and its metal-roof specification says no traffic for at least three days.

Weather limits

The makers cited here share one rule: the surface must be at least 5°F above the dew point. Minimum temperatures vary by product, from 32°F for Gaco's S42 and Everest's Silkoxy H3 to 40°F for Tremco's AlphaGuard Si 100 and American WeatherStar's 412 and 50°F for Karnak's 670HS.

The time it needs before rain varies too. Henry says its 887 is rain-safe in 15 minutes, Gaco's S42 and Momentive's Enduris 3500 ask for no rain within an hour, and Karnak and Sika want 24 hours clear.

Humidity speeds the cure and cold, dry air slows it. Tremco lists 2 hours between coats at 100°F and 90% humidity but 8 to 12 hours at 40°F and 20%, and Everest requires at least 20% humidity.

Ponding water

Silicone makers say their coatings hold up under standing water. Gaco says GacoRoof permanently withstands ponding water, Karnak says its 670HS does so without softening, and Momentive says Enduris is unaffected by standing water.

The same makers still call for positive drainage. Karnak's data sheet gives the test: no standing water on the roof 48 hours after it stops raining. Mule-Hide's specification uses the same 48 hours, which it attributes to NRCA, and requires remediation where water stays longer.

Warranties don't always follow the product claims. Everest says its warranties don't cover damage from ponding water. Sika rates its silicone ahead of acrylics on ponding but still requires areas that hold water more than 48 hours to be resloped for a warranty.

Where drainage isn't added, Mule-Hide's specification calls for at least one more gallon of silicone per 100 sq ft in ponding areas. Gaco's application specs ask for slope even under silicone: at least 1/4 inch per foot over asphalt roofs and 2:12 or more over metal panels.

Recoating and repairs

Plan on silicone for every future coat and repair. Gaco says to recoat its GacoRoof only with more GacoRoof, never acrylic or urethane, and Polyglass's first rule for repairs is that only silicone sticks to silicone. Henry's warranty is void if anything other than its coating or approved products goes over it.

New silicone can go over aged silicone without a primer in Gaco's and Karnak's instructions. Before any recoat, Gaco says the existing coating has to be identified, and Momentive strongly advises an adhesion test.

Coats on the same job have a window too: Karnak and Tremco say to apply the next coat within 24 hours, Henry says within 48 hours or the first coat may need washing, and Sika allows up to 7 days.

Reflectance and dirt

The Cool Roof Rating Council lists each rated coating's solar reflectance when new and after three years outdoors. White silicones start near 0.87 and lose part of it: Gaco's S4200 goes from 0.87 to 0.69, Henry's 887 and Tremco's AlphaGuard Si 100 from 0.87 to 0.67, and Sika's Sikalastic-500 from 0.88 to 0.67.

Makers say why. CertainTeed calls dirt retention a limitation of silicone, Polyglass says silicone is soft, a little tacky and picks up dirt easily, and Henry sells a dirt pick-up resistant formula.

Rough surfaces lose more: GAF's Unisil is rated 0.72 after three years on a smooth surface and 0.56 on a rough one. Granules help: Everest's Silkoxy H3 is rated 0.67 after three years plain and 0.73 with white granules.

Coating warranties don't cover looks. Momentive excludes color change from dirt, dust or organic growth, and Mule-Hide's system warranty excludes discoloration and staining for any reason.

Foot traffic and safety

Silicone-coated roofs are slippery, especially when wet. Henry calls them extremely slippery and a fall hazard, and Gaco says to use extreme caution on them when wet.

Specs add traction where people walk. Gaco and Neogard broadcast roofing granules into the wet top coat at 30 lb per 100 sq ft, and Sika recommends walkway pads or a non-skid surface wherever there's foot traffic. Momentive says its silicone shouldn't be considered for surfaces with frequent traffic.

Silicone lets some water vapor through, so Gaco, Everest and Momentive rule it out over cold storage buildings without a vapor barrier.

Warranties and thickness

Silicone warranties come in two kinds. A material warranty covers the coating: Momentive's replaces product that doesn't meet its data sheet, and American WeatherStar's says it makes no claim about stopping leaks. A no-dollar-limit (NDL) system warranty covers leak repairs without a cap; American WeatherStar's requires annual inspections and maintenance.

System warranties need an approved applicator. Gaco requires a current letter of good standing, Mule-Hide limits its system warranties to warranty-eligible contractors and requires a moisture survey, and Momentive may require an independent inspection of the dry mils.

Hail is excluded in both Momentive's product warranty and American WeatherStar's NDL warranty.

Makers tie the warranty term to the dry thickness, and the numbers differ by maker and by the roof underneath:

  • Momentive: 21, 28 and 36 dry mils for 10, 15 and 20 years, on a product warranty.
  • Sika: 23, 31 and 38 dry mils for 10, 15 and 20 years.
  • Mule-Hide, over concrete decks: 22, 29 and 36 dry mils for 10-, 15- and 20-year system warranties.
  • Neogard, over spray foam: an average of 30 dry mils for 10 years and 40 for 15, with a minimum at any point of 20 and 26.
  • Progressive Materials: 20, 25 and 30 dry mils over metal for 10, 15 and 20 years, but 30, 35 and 40 over modified bitumen and smooth built-up roofs.
  • Gaco: 34 dry mils in its metal-roof specification, which calls for a 20-year material and labor warranty.

Fire ratings

Silicone coatings are commonly listed Class A for fire under UL 790 (ASTM E108), but the class belongs to the whole roof assembly. Everest says its Silkoxy H3 is Class A over noncombustible decks and Class B over combustible ones.

Slope limits apply too. FM Approvals' report on American WeatherStar's Silicone 412, approved as a maintenance coating, lists Class A up to 5 in 12 over standing-seam metal but only up to 1 in 12 over modified bitumen and built-up roofs.

Miami-Dade approves Karnak's silicone only as a roof maintenance coating, not as a roof system under the Florida Building Code's high-velocity hurricane zone rules.

Other coatings

Roof systems

Calculator

Back to all roof coatings

Sources

  1. Henry Company, Technical Data Sheet: 887 Tropi-Cool 100% Silicone White Roof Coating (rev. 05/03/2022)
  2. Momentive Performance Materials, Enduris 3500 Silicone Roof Coating Technical Data Sheet (07/23/2025)
  3. Karnak Corporation, Roof Restoration System ASPHALT 405-670HS: application guidelines
  4. Gaco (Amrize Building Envelope), Product Data Sheet: GacoFlex S42 Series High-Adhesion 100% Silicone Coating (rev. 07/2026)
  5. Karnak Corporation, 670HS Karna-Sil Ultra high solids silicone coating product data sheet (05/30/24)
  6. Gaco (Amrize Building Envelope), Product Data Sheet: GacoRoof GR16 Series Silicone Roof Coating (revised 10/2022)
  7. ASTM International, ASTM D6694/D6694M-25, Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems
  8. Sika Corporation, Product Data Sheet: Sikalastic-500 Ultra High Solids Liquid Applied Silicone Roof Coating (November 2025)
  9. American WeatherStar, Product Data Sheet: Silicone 410 (PDS-092723)
  10. Tremco Roofing and Building Maintenance, AlphaGuard Si 100 data sheet
  11. Everest Systems, Technical Data Sheet: Silkoxy Ever-Tread walkpad
  12. Polyglass U.S.A., Inc., Maintenance Repairs on Silicone Coated Roofs (blog, updated August 2025)
  13. Momentive Performance Materials, Enduris Roof Coatings Limited Product Warranty (sample, rev. 02/24)
  14. Mule-Hide Products Co., System Specifications 04-1760: 100% Silicone Roof Coating System for Concrete Decks (February 2026)
  15. Momentive Performance Materials, Enduris Field Installation Guide: Silicone Recoat (08/25)
  16. Everest Systems, Technical Data Sheet: Silkoxy H3 High Solids Silicone Elastomeric Coating
  17. Polyglass U.S.A., Inc., PolyBrite 90.2 High Solids Silicone Roof Coating data sheet (edition date 10/24)
  18. American WeatherStar, Product Data Sheet: High-Solids Silicone 412 (PDS-121025)
  19. Cool Roof Rating Council, Rated Products Directory, roof products (downloaded October 18, 2026)
  20. CertainTeed, How to Improve Dirt-Pickup Resistance for Silicone Roof Coatings
  21. Gaco (Amrize Building Envelope), Application Specification ASP-S2000-22-10: GacoFlex S2000 Elastomeric Silicone Coating for Restoring Modified Bitumen and Smooth Built-Up Roofing (rev. 05/2020)
  22. Gaco (Amrize Building Envelope), Application Specification MR-S42-34-20: GacoFlex S42 Series Elastomeric Silicone Roof Coating for Restoring Aged Metal Roofing Systems (revised 10/2025)
  23. Momentive Performance Materials, Field Adhesion Testing, Enduris Roof Coating (08/25)
  24. American WeatherStar, Fluid-Applied Roofing Prep Manual
  25. Gaco (Amrize Building Envelope), Product Data Sheet: GacoFlex S20 Series Solvent-Free 100% Silicone Roof Coating (revised 08/2026)
  26. Neogard (a part of Hempel), Guide Specification: Silicone FR, Section 07 56 00 Fluid-Applied Roofing (July 2021)
  27. Gaco (Amrize Building Envelope), Application Specification RC-S42-34-20: GacoFlex S42 Series Elastomeric Silicone Coating for Recoating Elastomeric Roof Coating Systems (revised 07/2026)
  28. American WeatherStar, StarGard 15-Year Roof Coating Material Warranty (sample)
  29. American WeatherStar, StarGard 15-Year NDL System Warranty (sample)
  30. Progressive Materials (PM Silicone), Silicone Coverage Guide: How Much Coating Do You Need? (August 2024)
  31. FM Approvals (RoofNav report posted by American WeatherStar), Product Detail Report: AWS Silicone 412 (December 2025)
  32. Miami-Dade County, Product Control Section, Notice of Acceptance 25-0402.09: Karnak Coating Systems (approved September 11, 2025)

Updated October 2026.